AskDefine | Define timber

Dictionary Definition

timber

Noun

1 the wood of trees cut and prepared for use as building material [syn: lumber]
2 a beam made of wood
3 a post made of wood
4 land that is covered with trees and shrubs [syn: forest, woodland, timberland]
5 (music) the distinctive property of a complex sound (a voice or noise or musical sound); "the timbre of her soprano was rich and lovely"; "the muffled tones of the broken bell summoned them to meet" [syn: timbre, quality, tone]

User Contributed Dictionary

English

Etymology

tymber from timber

Pronunciation

  • a UK
    • sense Noun /ˈtɪmbə(ɹ)/, /"tImb@/
    • sense Interjection /ˈtɪːmˌbəː(ɹ)/, /"tI:m%b@:(r)/
  • a US
    • sense Noun , /ˈtɪmbɚ/, /"tImb@`/
    • sense Interjection /ˈtɪːmˌbɚː/, /"tI:m%b@`:/
  • Hyphenation: tim·ber
  • Homophones: timbre

Noun

  1. Trees in a forest regarded as a source of wood.
  2. Wood that has been pre-cut and is ready for use in construction. lumber.
  3. A heavy wooden beam, generally a whole log that has been squared off and used to provide heavy support for things such as roof; also (historically) in the plural, as in ship's timbers.

Synonyms

  • (trees considered as a source of wood)
  • (wood that has been cut ready for construction): lumber, wood
  • (beam used to support a roof): beam, rafter

Translations

trees considered as a source of wood
wood that has been cut ready for construction
beam used to support a roof
  • Dutch: dakbalk
  • Finnish: hirsi
  • Japanese: 梁 (はり)
  • Kurdish: karîte
  • Norwegian: takbjelke
  • Spanish: viga , polín

Interjection

timber!
  1. Used by loggers to warn others that a tree being felled is falling.

Translations

warning shout used by loggers

Old English

Etymology

Common Germanic *timram, whence also Old High German zimbar (German Zimmer), Old Norse timbr and Gothic ̹̼̰̈́͂̾̽ (timrjan) to build, derived from Proto-Indo-European *dem(H₂)-, build, house

Noun

timber
  1. timber
  2. a building
  3. the act of building

Extensive Definition

Lumber or timber is wood in any of its stages from felling through readiness for use as structural material for construction, or wood pulp for paper production. Timber often refers to the wood contents of standing, live trees that can be used for lumber or fiber production, although it can also be used to describe sawn lumber whose smallest dimension is not less than 5 inches (127 mm).
Lumber is supplied either rough or finished. Besides pulpwood, rough lumber is the raw material for furniture-making and other items requiring additional cutting and shaping. It is available in many species, usually hardwoods. Finished lumber is supplied in standard sizes, mostly for the construction industry, primarily softwood from coniferous species including pine, cedar, hemlock, fir and spruce, but also some hardwood for high-grade flooring.

Dimensional lumber

Dimensional lumber is a term used for lumber that is finished/planed and cut to standardized width and depth specified in inches. Examples of common sizes are 2×4 (also two-by-four and other variants such as four-b'-two in Australia), 2×6, and 4×4. The length of a board is usually specified separately from the width and depth. It is thus possible to find 2×4s that are four, eight, or twelve feet in length. In the United States the standard lengths of lumber are 6, 8, 10, 12, 14, 16, 18, 20, 22, and 24 feet. Solid dimensional lumber typically is only available up to lengths of 24 ft, yet since builders have a need for lengths beyond that for roof construction (rafters), builders use "finger-jointed" lumber that can be up to 36 ft long in 2×6 size (see Engineered Lumber below). Finger-jointed lumber is also widely used for smaller lengths like studs, the vertical members of a framed wall. Pre-cut studs save a framer a lot of time as they are pre-cut by the manufacturer to be used in 8 ft, 9 ft & 10 ft ceiling applications, which means they have removed a few inches of the piece to allow for the sill plate and the double top plate with no additional sizing necessary by the framer.
In the Americas, two-bys (2×4s, 2×6s, 2×8s, 2×10s, and 2×12s), along with the 4×4, are common lumber sizes used in modern construction. They are the basic building block for such common structures as balloon-frame or platform-frame housing. Dimensional lumber made from softwood is typically used for construction, while hardwood boards are more commonly used for making cabinets or furniture.
The nominal size of a board varies from the actual size of the board. This is due to planing and shrinkage as the board is dried. This results in the final lumber being slightly smaller than the nominal size. Also, if the wood is surfaced when it is green, the initial dimensions are slightly larger (e.g. 1/16 in bigger for up to 4 in nominal lumber, ⅛ in for 5 in and 6 in nominal lumber, ¼ in bigger for larger sizes). As the wood dries, it shrinks and reaches the specified actual dimensions.

Non-North American sizes

Outside North America sizes of timber can vary slightly. Sizes are, in some cases, based on the imperial measurement and referred to as such; in other cases the sizes are too far removed from the imperial size to be referred to by imperial measurement. Lengths are sold every 300 mm (a metric approximation of 1 ft). Common sizes are similar to the North American equivalent; 2.4, 2.7, 3.0, 3.6, 4.2, 4.8, 5.4, 6.0.

Hardwoods

In North America sizes for dimensional lumber made from hardwoods varies from the sizes for softwoods. Boards are usually supplied in random widths and lengths of a specified thickness, and sold by the board-foot (144 cubic inches, 1/12th of a cubic foot). This does not apply in all countries, for example in Australia many boards are sold to timber yards in packs with a common profile (dimensions) but not necessarily of consisting of the same length boards. Hardwoods cut for furniture are cut in the fall and winter, after the sap has stopped running in the trees. If hardwoods are cut in the spring or summer the sap ruins the natural color of the timber and deteriorates the value of the timber for furniture.
Also in North America hardwood lumber is commonly sold in a “quarter” system when referring to thickness. 4/4 (four quarters) refers to a one-inch thick board, 8/4 (eight quarters) is a two-inch thick board, etc. This system is not usually used for softwood lumber, although softwood decking is sometimes sold as 5/4 (actually one inch thick).

Engineered lumber

Engineered lumber is lumber created by a manufacturer and designed for a certain structural purpose. The main categories of engineered lumber are:
  1. Laminated Veneer Lumber (LVL) – LVL comes in 1-3/4 inch thicknesses with depths such as 9-1/2, 11-7/8, 13, 16, 18, or 24 inches, and are typically doubled or tripled up. They function as beams to provide support over large spans, such as removed support walls and garage door openings, places where dimensional lumber isn't structurally sound to use, and also in areas where a heavy load is bearing from a floor, wall or roof above on a somewhat short span where dimensional lumber isn't practical. This type of lumber cannot be altered by holes or notches anywhere within the span or at the ends, as it compromises the integrity of the beam, but nails can be driven into it wherever necessary to anchor the beam or to add hangers for I-joists or dimensional lumber joists that terminate at an LVL beam.
  2. Wood I-joists – Sometimes called "TJI®" or "Trus Joists®", both of which are brands of wood I-joists, they are used for floor joists on upper floors and also in first floor conventional foundation construction on piers as opposed to slab floor construction. They are engineered for long spans and are doubled up in places where a wall will be placed over them, and sometimes tripled where heavy roof-loaded support walls are placed above them. They consist of a top and bottom chord/flange made from LVL with a webbing in-between made from oriented strand board (OSB). The webbing can be removed up to certain sizes/shapes according to the manufacturer's or engineer's specifications, but for small holes, wood I-joists come with "knockouts", which are perforated, precut areas where holes can be made easily, typically without engineering approval. When large holes are needed, they can typically be made in the webbing only and only in the center third of the span; the top and bottom chords cannot be cut. Sizes and shapes of the hole, and typically the placing of a hole itself, must be approved by an engineer prior to the cutting of the hole and in many areas, a sheet showing the calculations made by the engineer must be provided to the building inspection authorities before the hole will be approved. Some I-joists are made with W-style webbing like a truss to eliminate cutting and allow ductwork to pass through.# Finger-Jointed Lumber – Solid dimensional lumber lengths typically are limited to lengths of 22 to 24 feet, but can be made longer by the technique of "finger-jointing" lumber by using small solid pieces, usually 18 to 24 inches long, and joining them together using finger joints and glue to produce lengths that can be up to 36 feet long in 2×6 size. Finger-jointing also is predominant in precut wall studs.
  3. Glu-lam Beams – Created from 2×4 or 2×6 stock by gluing the faces together to create beams such as 4×12 or 6×16. LVL beams have taken their place in most home construction.
  4. Manufactured Trusses – Trusses are used in home construction as bracing to support the roof rafters in the attic space. It is seen as an easier installation and a better solution for supporting roofs as opposed to the use of dimensional lumber's struts and purlins as bracing. In the southern USA and other parts, stick-framing with dimensional lumber roof support is still predominant. The main drawback of trusses is that less attic space is usable.
  5. Oriented Strand Board (OSB) – OSB is made by laminating large, thin wood chips with glue, such that the grain orientation of the chips is random, making the OSB panels equally stiff in all directions. OSB has replaced plywood for use as exterior wall sheathing and roof decking (7/16 inch minimum thickness) and in second-story flooring (3/4 inch thickness in a tongue-and-groove interlocking pattern), which is nailed and glued to the I-joists. OSB used in wall sheathing and roof decking will swell if exposed to the elements for even a brief time and must be replaced; therefore, it is covered by a weatherproof membrane such as felt or spun-bonded olefin (Tyvek®) to protect it, secured with plastic cap nails. House wrapping is used on areas which will be sheathed with vinyl siding. 3/4 inch tongue-and-groove OSB flooring is coated to protect it from the elements for a short time until the structure is roofed over. Moisture resistant OSB is often specified for use as a roof underlayment.

Defects in lumber

Defects occurring in Timber are grouped into the following five divisions:

Defects due to conversion

During the process of converting timber to commercial form, the following defects may occur:
  1. Chip mark
  2. Diagonal grain
  3. Torn grain
  4. Wane

Defects due to fungi

Fungi attack timber only when the following two conditions are satisfied simultaneously:
  1. The moisture content of the timber is above 20%
  2. There is presence of air and warmth for the growth of fungi.
If any of the above condition is absent, decay of wood due to fungi would not occur. Hence, dry wood due having moisture content less than 20 per cent will remain sound for centuries. Similarly, wood submerged in water will not be attacked by fungi because of absence of air. Following defects are caused in timber by fungi:
  1. Blue stain
  2. Brown rot
  3. Dry rot
  4. Heart rot
  5. Sap stain
  6. Wet rot
  7. White rot

Defects due to insects

Following are the insects which are usually responsible for the decay of timber:
  1. Beetles
  2. Marine Borers
  3. Termites

Defects due to natural forces

The main natural forces responsible for causing defects in timber are two, namely, abnormal growth and rupture of tissues.

Defects due to seasoning

Defects due to seasoning are the number one cause for splinters and slivers.

References

л

External links

timber in Danish: Tømmer
timber in German: Bauholz
timber in Spanish: Madera
timber in French: Bois (matériau de construction)
timber in Italian: Legname
timber in Norwegian: Tømmer
timber in Norwegian Nynorsk: Tømmer
timber in Polish: Tarcica
timber in Portuguese: Madeira
timber in Russian: Бревно
timber in Finnish: Puutavara
timber in Swedish: Timmer

Synonyms, Antonyms and Related Words

afforestation, arboretum, balk, bare pole, beam, beams, billet, board, boarding, boards, boondocks, bush, bushveld, character, chase, clapboard, climax forest, cloud forest, conifer, cord, cordwood, deal, dendrology, driftwood, evergreen, firewood, forest, forest land, forest preserve, forestry, fringing forest, fruit tree, gallery forest, girder, greenwood, hanger, hardwood, hardwood tree, index forest, jungle, jungles, lath, lathing, lathwork, log, lumber, mast, material, national forest, palmetto barrens, panelboard, paneling, panelwork, park, park forest, pine barrens, plank, planking, planks, plyboard, plywood, pole, pollard, post, potential, primeval forest, prospect, protection forest, puncheon, quality, rafter, rain forest, reforestation, sapling, scrub, scrubland, seedling, selection forest, shade tree, shake, sheathing, sheathing board, sheeting, shingle, shrubland, sideboard, siding, silviculture, slab, slat, softwood, softwood tree, spar, splat, sprout forest, stand of timber, state forest, stave, stick, stick of wood, stovewood, stuff, talent, three-by-four, timber tree, timbering, timberland, timberwork, tree, tree veld, two-by-four, virgin forest, weald, weatherboard, wildwood, wood, woodland, woods
Privacy Policy, About Us, Terms and Conditions, Contact Us
Permission is granted to copy, distribute and/or modify this document under the terms of the GNU Free Documentation License, Version 1.2
Material from Wikipedia, Wiktionary, Dict
Valid HTML 4.01 Strict, Valid CSS Level 2.1